BLC questions

12 replies
ST
Stan
Bronze
1810 posts
Posted July 15, 2023 at 03:16 GMT
#687795
I recently picked up a BLC and I'm having some challenges getting it setup.  On the ML side, I have a BS5 and BL3500.  On the NL side, I have various devices, but focusing on the BS1 Gen2 GVA for now.
  1. My audio master is a BS5 set to audio master mode
  2. My BLC is set to video master
  3. I have B&O Radio on my BS1 mapped to TV on the ML side
  4. I have all of the ML source turned on for the NL experience
Problem #1:  My BS5 is only responding to CD and Radio (which I have mapped to N.Music and N.Radio within the BS5).  When I press TV, nothing happens.  However, in my link room, I can press TV and my BL3500 plays B&O Radio from the BS1. A little background here:  I originally had the BLC setup as an AV.Master as that is how it was configured when I received it.  After doing some configuration and testing I recognized the conflict and set the BLC role to V.Master.  However, the system was still wonky so I disconnected and powered off the BLC.  At this point, I had difficulty getting the BLC to boot up correctly - flashing green light that never went away, tried factory reset, etc. nothing helped - so I disconnected over night and this morning all is fine... Problem #2:  I can't see any of the ML sources in the BeoApp.  I'm assuming CD and Radio should show up there as a source option, correct? I guess my next step is to power down the BS5, and possibly the BL3500 to do the "ML reset", but I was hoping to avoid that as my BM5 is kind of hard to reach, and I'm paranoid about the BLC not rebooting if I power it off as well...  Mostly curious if I'm overlooking something.
ST
Stan
Bronze
1810 posts
Posted July 15, 2023 at 16:01 GMT
#702721
I was missing something for the BS5 configuration.  I had to set the audio option to 2 on the BS5 for it to respond to non-BS5 commands like TV.  It was set to 1 by default, I assume, when I switched it to audio master.  For most of its life, the BS5 worked with a BS9000 so I never had it set to audio master until recently (when my BS9000 died and has yet to be fixed). Still not sure how to see the ML sources from the NL side of the world.  I guess I will dig into the old forum...
ST
Stan
Bronze
1810 posts
Posted July 15, 2023 at 16:10 GMT
#702722
Figured out the NL side as well.  Need to add the BLC as a product to the B&O App. Well, I had a nice conversation with myself here :D
ST
Stan
Bronze
1810 posts
Posted July 15, 2023 at 17:38 GMT
#702723
Is there a more direct way to listen to ML sources in the NL world than playing the ML source on the BLC, then joining the NL device to the BLC?
XA
XavierItzmann
Bronze
234 posts
Posted July 16, 2023 at 04:14 GMT ? Edited July 16, 2023 at 04:14 GMT
#702725
On my NL network I have an A6, like so: From the B&O app, while the A6 is selected, I can depress the three dots on the lower right hand side and I get the following options, plus CD, A.AUX, LINE IN, N.RADIO, Open Spotify App, and Standby. The sources local to the A6, such as B&O Radio, are reliable.  The sources remote to the A6, such as N.RADIO or N.MUSIC, are very unreliable when called up directly from the A6. To make the system behave reliably, I activate sources that are local —such as CD on the wired Master Link, or Deezer on the A6— and then JOIN from or to the other environment. Yeah, the BLC is a bit wonky, apparently.
carolpa
carolpa
Bronze
2504 posts
Posted July 16, 2023 at 10:48 GMT
#702732
carolpa
carolpa
Bronze
2504 posts
Posted July 16, 2023 at 10:58 GMT
 The sources remote to the A6, such as N.RADIO or N.MUSIC, are very unreliable when called up directly from the A6.
How reliable is the old Airplay Express in this setup? I find all my BLC reliable, but all of them are wired LAN connected.
trackbeo
trackbeo
Bronze
897 posts
Posted July 16, 2023 at 16:59 GMT
#702739
My experience has been that 3rd generation (the with-separate-power-cord type) is still going strong, both as a solid, never-reboot AirPlay2 (with the last firmware) endpoint and as a gateway of wired Ethernet to the "main" Wi-Fi router.  The 1st generation (integrated-plug) has started to fail, sometimes seemingly having little Wi-Fi range, though it's usually the tough-to-repair power supply at fault. Hopefully @XavierItzmann will reply too.
ST
Stan
Bronze
1810 posts
Posted July 16, 2023 at 17:36 GMT
#702741
Configuring "Link to other product” setting as Carolpa suggested did the trick.  Thanks for the help everyone!
ST
Stan
Bronze
1810 posts
Posted July 17, 2023 at 15:06 GMT
#702754
Also, I've been using an Airport Express 3rd gen for quite a few years in a manner similar to XavierItzmann's diagram above (providing a wireless ethernet connection for my BS5).  It works fine.  Similarly, I had an earlier version that went wonky.
or
BeoWorld Gold Membership card
Join BeoWorld

Register to access the forums, reference material, and exclusive member benefits — including our monthly prize draw.

Become a Member

December 2026 Prize Draw

Gold Members Only

As a Gold member you're automatically entered into our exclusive prize draw — your chance to win iconic Bang & Olufsen products. A unique benefit of BeoWorld Gold membership, every draw brings a new opportunity to win something special.

View Prize Go For Gold
BeoSound Level

1st Prize

BeoConnect Core

2nd Prize

BeoRemote Halo

3rd Prize